What SEER2 rating should I get for a heat pump in Frisco?

For most Frisco homes, a 15-16 SEER2 single or two-stage heat pump is the value sweet spot, while variable-speed models near 18-20 SEER2 make sense for larger two-story homes or anyone prioritizing humidity control and quiet operation. We size from a Manual J load calc rather than just matching the old unit, so the rating you pay for actually performs.

Should I consider a dual-fuel system in Frisco?

Dual-fuel pairs a heat pump with a gas furnace, letting the heat pump handle the mild North Texas winter efficiently and switching to gas for the occasional hard freeze. It costs more up front but can lower heating bills and keep you comfortable on the coldest nights. We'll run the numbers for your home.

How long does heat pump installation take in Frisco?

Most Frisco replacements take 1-2 days, covering removal of the old equipment, the line set, evacuation and proper refrigerant charge, airflow setup, and the permit. We commission the system before we leave so the defrost cycle and thermostat are confirmed working.

Right-sized SEER2 and HSPF2 heat pumps for the homes built in Frisco's 2008-2015 boom.

Heat Pump Installation in Frisco, Texas

Heat pump installation in Frisco, TX. Manual J load sizing, matched coil and condenser, and dual-fuel options for North Texas winters. Systems from $4,200 with a 10-year warranty.

Licensed & Insured

4.9★ Rating

Same-Day Service

24/7 Emergency

Heat Pump Installation in Frisco is a professional HVAC service provided by Jupitair HVAC in Frisco, Texas. Our licensed technicians serve Frisco with same-day appointments, transparent pricing, and 90-day warranties on repairs. In Frisco, TX, heat pump installation in frisco typically costs $89-$15,000 , with same-day service, 2-hour emergency response service available.

Local Frisco technicians
Same-day service
90-day warranty
15+ years experience

Looking for HVAC services near me in Frisco? Jupitair HVAC provides professional AC repair, furnace service, emergency HVAC, heat pump installation throughout all Frisco neighborhoods, including Frisco, North Texas. We offer same-day service with typical response times under 2 hours for emergency calls. Our local technicians are familiar with Frisco's housing styles, common HVAC issues, and permit requirements.

Heat Pump Installation Done Right in Frisco

A lot of Frisco's housing stock went up between 2008 and 2015, and those original builder systems are now reaching the 12-to-15-year mark where a full replacement makes more sense than another repair. A heat pump is a strong fit for North Texas, where mild winters let it run efficiently on electricity most of the season. The catch is sizing: we run a Manual J load calculation on your actual home instead of just matching the old tonnage, then pair a matched coil and condenser so the SEER2 and HSPF2 ratings you pay for actually show up on the meter. If you'd rather keep gas heat for the coldest nights, compare with our furnace installation in Frisco, or ask us about a dual-fuel setup that uses both.

Variable-speed options up to 20 SEER2

Manual J load sizing, not a tonnage guess

10-year comprehensive warranty coverage

Dual-fuel option for the coldest nights

Call NowCall (940) 390-5676 Get Free Energy Assessment

Why a Heat Pump Fits Frisco

✓ Mild North Texas winters keep it in efficient mode most days
✓ One system handles both heating and cooling
✓ Variable-speed models hold steady temps and dehumidify better
✓ Newer R-454B and R-410A refrigerants supported
✓ Dual-fuel pairs it with a gas furnace for hard freezes

Ask About Rebates & Tax Credits

High-efficiency heat pumps can qualify for federal energy tax credits and utility rebates. We'll tell you what your equipment qualifies for.

15-20 SEER2

Efficiency Range

Single to variable-speed

$4,200

Installs Start At

Matched heat pump system

1-2 Days

Install Time

Most Frisco replacements

10 Years

Equipment Warranty

Plus 2-year labor

How We Size and Install in Frisco

The published efficiency rating only matters if the system is sized and charged correctly. Here's how we get it right.

Manual J Load Calc

We size to your home's actual heat gain and loss, not just the old unit's tonnage, so it isn't oversized

Match the System

Coil, condenser, and air handler matched as a set so the rated SEER2 and HSPF2 actually hold up

Line Set & Charge

New or flushed line set, evacuated to vacuum, and charged by subcooling to the exact spec

Commission & Permit

Airflow set, defrost verified, permit pulled, and the thermostat configured before we leave

Get a Right-Sized Quote in Frisco

If your builder-grade system is on its last legs, we'll run the load calc and walk you through single-stage, two-stage, and variable-speed options with honest numbers, no pressure. If it's a repair you need first, our Frisco heat pump repair team can take a look.

Call NowCall Now: (940) 390-5676 Schedule Energy Consultation